AVAILABLE EQUIPMENT
(All equipment shown on this page is subject to prior sale.)

Used 8" x 8", 15 Ton Hand Pump Presses (P-685 to 688)
Electrically heated platens, 6" daylight, 4" diameter ram, temperature controllers, four (4) presses available
As-Is, In Good Operating Condition


SPECIAL PRICE
$2,950.00 Each

Rebuilt C2 Preformer (MC-61)
New electrical controls, includes vacuum system, flying cutter head and conveyor, One year warranty - $64,600.00


SPECIAL PRICE
$58,000.00

24" x 36" Platen Size, 300 ton, 4-post Hydraulic Press (P-490) - 15" daylight (adjustable from 7" to 53"), 11 1/2" stroke, strip heaters, full circle bronze guides, pull back cylinders As-Is - $12,000.00

Used Intensive Mixer (MX-29) Midget Size: .67 pound batch, 220 V AC 3 Ph two speed brake motor, spray bells, table mounted - $5,500.00

Partial List
Rebuilt or As-Is Equipment
On Our Floor Ready to Go

LABORATORY EQUIPMENT

New LM Series Silicone/Rubber Mills - Cabinet style, chromed rolls, rotary unions, inboard grease seals, one year warranty, available in three sizes: 6" x 6" x 13" (model LM-613), 8" x 8" x 16" (model LM-816), or 10" x 10" x 24" (model LM-1024) - LM-613 pictured above and on mixers/mills page

New LP Series Hydraulic Lab Presses - Self-contained, four post configuration, electrically heated platens, one year warranty, available in three sizes: 40 ton - 12" x 12" platen (model LP-1240), 50 ton - 15" x 15" platen (model LP-1550), or 75 ton - 18" x 18" platen (model LP-1875) - LP-1240 pictured above and on presses page

PRODUCTION EQUIPMENT

(9)  24" x 24" Platen Size, 150 ton, slab-side hydraulic presses (P-613 - P-621) up acting, 12" piston, 19" and 26" daylight bolster to bolster, excellent condition

(5)  24" x 24" steam platens 18" dia. ram, 18" stroke slab-side hydraulic EEMCO presses (P-669 - P-673) with (2) 10" daylights gib guides, no hydraulics or electrical controls

(3)  40" left to right x 20" front to back Platen Size, 125 ton, 4-post hydraulic presses (P-678 - P-680) up acting, (2) 9" rams, babbitted bolster guides 18" stroke and daylight, steam platens, two w/ pullback cyls., no hydraulics or electrical controls

Silicone Mixer (MX-37) - Tilting tub, 220 V AC motor, 35-50 pound batch size, motor and controls - $37,500.00

22" x 22" x 68" Unitized Top Cap Rubber Mill (ML-139) - 100 HP 440 Volt AC motor, without motor control panel, As-Is - $12,500.00

IN PRODUCTION

14" x 14" x 30" Adamson Rubber Mill, Used (ML-68) - Unitized, top cap, no motor or controls

16" x 16" x 40" Farrel® Rubber Mill, Used (ML-131) - Unitized, end cap, no motor or controls
Farrel is a registered trademark of Farrel Corporation, Ansonia, CT

READY FOR REBUILDING

Heidrich Used Stock Cutter (MC-82) - 36" wide by 82" long belt area, 2 HP brakemotor

Intensive mixer (ML-33) - Approx. 125 pound charge, slide door, roller bearing rotors, SSA dust seals, hopper, floating weight and cylinder, cast iron base, 200 HP gearbox, less motor and controls - Rebuilt price - $85,000.00
Price, 200 HP rebuilt DC motor, new SCR drive, motor control panel - $125,000.00